Cobra Engineering Tensioner

The stock Ford tensioner on the passenger side puts tension on the driven side on the passenger side. This allows for a variation in intake cam timing. This tensioner body swaps the piston 180* to apply tension the slack side. This requires the...

Comp Cams 4.6/5.4 XE262A - 106100

These are a graet cam set for a mildy modded vehicle that where low and midrange power is desired. With a manual trans and headers you can expect power in the 350rwhp range.   More Information UPC 036584096399 Manufacturer COMP...

Comp Cams 4.6/5.4 XE262A - 106300

This is a good cam set for mild setup where a relatively smooth idle and good vacuum is desired. Xtreme Xtreme Energy™-R 226/224 Hydraulic Roller Finger Follower Cams for Ford 4.6/5.4/5.8L Modular 4 Valve Xtreme XE-R 226/224 Hydraulic Roller Finger...

Comp Cams 4.6/5.4 XE266B - 106160

These are the most aggressive of the stock spring capable options. We recommend at least a 4.10 rear gear and a manual trans.  Xtreme RPM 230/230 Hydraulic Roller Finger Follower Cams for Ford 4.6/5.4/5.8L Modular 4 Valve Xtreme RPM 230/230...

Comp Cams 4.6/5.4 XE266B - 106360

These cams are good for a moderate to high power supercahrged or nitrous build.  Expect good power to 7500 with high boost. Can be used in n/a setups also if more peak power is desiredd without adding Requires valve springs. Xtreme Energy™-R...

Comp Cams 4.6/5.4 XE270A - 106200

These cams are a good set for a moderately modded vehicle. They require at leaast 4.10 gears as low and midrange power will be reduced.  Also, they are stock spring capable.   Advertised Intake Duration 269 Advertised Exhaust...

Comp Cams 4.6/5.4 XE270B - 106400

These require 3.73 or 4.10 gears and a 3600 stall if using an automatic trans. Power in a stock engine will be in the 360-370 range with significant tq losses down low.  The idle will be choppy. Xtreme XE-R 234/232 Hydraulic Roller Finger Follower...

Comp Cams 4.6/5.4 XE274B - 106460

These are for the most aggressive supercharged setups. The idle will be very choppy and drivability issues are to be expected. Xtreme XE-R S-Charged/N2O 238/240 Hydraulic Roller Finger Follower Cams for Ford 4.6/5.4/5.8 Modular. Max strip/street cams for...

Comp Cams 4.6/5.4 XE278A - 106500

These are the most aggressive of the n/a camshaft offerings.  4.10 or steeper gears are required as well as a very high stall converter if an auto trans is used. Xtreme XE-R 242/240 Hydraulic Roller Finger Follower Cams for Ford 4.6/5.4/5.8L Modular...

COMP Cams 92-11 Ford Modular 4.6L DOHC Performance Lash Adjusters - Set of 32 - 84031-32

Lash adjusters in Ford Modular engines can leak down under high RPM, causing lost duration and lift, as well as increased valve train wear. The COMP Cams Ford Modular Performance Lash Adjusters are engineered to have a slower bleed down rate compared to...

COMP Cams Socket For CS Crank - 4793CPG

The COMP crankshaft socket for Chevrolet Small Block, 90 degree V6, GM 4 cyl and Ford 4.6 is the last crankshaft socket that you'll need. Featuring a 1/2" drive socket and a knurled nut, our socket is designed for use with a degree wheel.CatalogUser 1

Diamond 5.8 GT500 pistons, 8.5:1 compression

1.32 CD and a 31cc dish volume for an 8.5:1 compression   Piston Features: 3D milling on piston crowns for ready to install finish Offset pins for quiet operation Moly skirt coating for friction loss and skirt wear protection Ratios figured for 3...